Clik here to view.
Trouble Shooting Electrical Cabinet
I'm trying to diagnose my electrical cabinet. I'm getting no power for any of the motor lines (u4/v4/w4/u8/v8/w8). I took a picture of the cabinet. This is what I'm using, I am told it is the correct...
View ArticleDeckel FP4MA mill with contour 2
I have just bought an old Deckel FP4MA mill from 1988. Can anyone provide me with basic instructions on how to operate the control system. Also the machine shows a flashing FP03 at the bottom of the...
View ArticleUgliest European Mill Ever
Crikey, I used to think my FP1 had a face only a mother could love, until I saw this Beichle. It may be well designed for die-sinking, but you would have to hide it out the back, and throw a tarp over...
View Article4MT Collets from RDG (UK) - fit to FP1?
Has anybody checked out the fit of these collets to an FP1. They appear to be shorter than tanged ones and have 16mm thread on the inside which could be used to adapt to them for 20 mm buttress thread....
View ArticleThe oldest Deckel ever
Looks like a real Friedrich Deckel machine. Deckel Universalfräsmaschine **HISTORISCH**SAMMLERSTÜCK** in in München | eBay
View ArticleClik here to view.
Kunzmann WF600MC Pictures
More pics in the next post. One can see the difference between the Orientated Spindle Stop and that without. 1. The "Minimum Quantity Lube system" made by TKM. It is considerably more expensive that...
View ArticleDeckel FP4MA mill with contour 2 - Stuck on lower Z-limit switch
I have a FP4MA with contour 2 control. The machine is 2.5D so the Y and Z axis are driven by the same servo which is mechanically switched between the two axis. My problem is that I recieved the mill...
View ArticleClik here to view.
New FP2 'Active' owner down under
Hi guys long time reader here just letting you know I have joined the Deckel Club ....Deckel FP2 'Active' delivered to my shed in Melbourne from Sydney...however some poor handling during shipping sees...
View ArticleClik here to view.
Bought a nice Deckel FP42NC with D11 ...........But with some missing boards
I bought this Deckel FP42NC today Looking at the pictures it is beautiful machine with full enclosure And I am sure there is a market in germany for a machine like this But............. It is missing...
View ArticleFP2NC Y axis unstable
Hi all. My Y axis movement has become very unstable. At speeds above 1000mm/min, it oscillates. This has happened many times before, and the cure has always been to clean the tacho. This time, it isn't...
View ArticleClik here to view.
Fp3 makes a Gasket Mold
Just finished up a prototype mold for a 14.5" seal gasket on my Fp3nc with the 3m control and NCT400 table. The job is too big for my lathe.(17.25 dia.) The material is alum. tooling plate. Attached...
View ArticleClik here to view.
Röhm 85mm three-jaw chuck is tight
Hi Group, The used milling machine that I purchased a couple of months ago came with two cabinets full of tooling, which I am still working my way through. This includes several Röhm 3 and 4-jaw...
View ArticleDeckel FP1 forward & reverse ?????????????!!!!!!!!!!!!
I want to turn my FP1 milling machine backwards, in reverse! Can I do this? Without doing any damage to the machine internals"" this will be in vertical & horizontal work. Please do not reply if...
View ArticleClik here to view.
Info needed Deckel Dividing Head
Hi everyone, I recently acquired a second lathe (cardiff major) and it came with a load of accessories. Included is what I believe to be a Deckel/Alexander dividing head. I am more inclined that it is...
View ArticleDeckel FP2 oil nipples - which thread?
Hi guys. I am following Bruce's thread - and also others, that pop up because of his. I happen to have the same problem, although I hope the damage is just a recent mistake. Earlier I have looked at...
View ArticleClik here to view.
40 Taper Collets
Picture shows the drawing for collets, factory has few inch and metric sizes in stock, no hex or square. I have used and sold collets from them over the years, never had a problem. Price will be $23...
View ArticleDeckel S11 tool grinder
HELP!! Where can i find a users manual for a Deckel S11 tool and cutter grinder?
View ArticleSource for Deckel buttress thread tap and die
I thought there was a post about this some time ago, but I can't find it. Has anyone come across a source for Deckel buttress thread tap and die.
View ArticleAnyone replace the bearing in an FP2 horizontal arbor support?
Anything I need to know? Just press out and back in? Any advice? Thanks.
View ArticleDeckel 2236 rotary/tilt table, right size for an FP2?
Is a Deckel 2236 rotary/tilt table a good choice for a 1967 FP2 (500 x 200 x 400 mm travel)? Some searching of old PM threads indicate that it was intended for the FP4 and is too large for an FP2.
View Article