How do i remove the drawbar on a maho mh700?
There is a tapered pin right under the square stud at the top of the draw bar. I removed the pin but i couldn't remove that top cap. I would like to remove the drawbar to change out the S20x2 buttress...
View ArticleFirst generation FP3, is horizontal quill spoke supposed to be easily...
Or is it supposed to be permanently attached via two set screws ? I ask as the set screws are seized on mine and I wondered if it could otherwise be removed and used with the vertical head 12mm square...
View ArticleDeckel Dialog 11 error code book / list?
I am looking for an Deckel dialog 11 error code book or some kind of list were all the error codes are described in. Does this exist and we're can I find it? Thanks Oscar Skickat från min iPhone med...
View ArticleMikron for sale cheap
Hello Guys Asking $18K for the machine,needs to go. I have a semi local customer to me with a Mikron for sale. They are going out of business. The machine has New Z Axis Ballscrew, Freshly rebuilt...
View ArticleDeckel FP50CC/T Spindle Speed Changer Won't Go Anymore
Well, after a few years of getting the Deckel FP50CC/T going, today it seems it doesn't want to go to high speed anymore. The machine will go 'clink, clink, clunk, clink' as the gears try to line up....
View ArticleMaking a new drawbar for a MAHO mh700
I removed the s20x2 female buttress thread drawbar I am changing over to mt4 taper with 5/8-11 female so i am going to make a 5/8-11 drawbar with a male end Question: the stock buttress drawbar was...
View ArticleMaho700 horizontal spindle drive gear
I need to remove the drive gear of a Maho700 horiz spindle to replace the bearing. Has anybody done that and how ? It seems to be secured with a pin from the side of the casting but I drew a blank...
View ArticleClik here to view.
Piggy back spindle mount
I am going to mount a Makita trim router to the quill of my Deckel FP4NC and am looking for opinions on my design. I will be using this spindle for machining wood with mostly 1/8" shank end mills down...
View Articlelooking for a dovetail cutter
I need a good quality but not crazy expensive dovetail cutter for making some smallish parts in cast iron. (150mm/6 inch long 18mm deep dovetails) I don't want Chinese junk but the only only other...
View ArticleClik here to view.
FP4NC at work
Ok this is in the manner of a test.. Since my loss of a hosting service (Photobucket) by their change in use policy, i wanted to see if i have gotten the posting of photos that are hosted within this...
View ArticleStrange?? FP2 Coolant Pump Pipe
Hi Folk My FP2 came without a coolant system and I'm now rebuilding the system to it's original state. I've got the FP2 Coolant pump and associated chain and it's connected running as it should. I know...
View ArticleAcieraF1 for sale
I have an Aciera F1 for sale has all accessories including DRO If interested contact entoffice@aol.com and put Aciera F1 for sale in subject
View ArticleClik here to view.
Rawyler FT2?
While at auction and having passed on a Aciera F1, I picked up a Rawyler FT2. It is in fairly good shape, but was a production machine and slightly different than what i've found on internet. It does...
View ArticleMoving a Deckel GK21
Hi, all. I'm a brass instrument maker about to set up a home shop off the back of an old Belgian rowhouse, and am trying to figure out if I can get a Deckel GK21 (1040 x 1250mm / 41 x 49.2 inches...
View ArticleWhat MT4 tooling for a FP1? Deckel only, any MT4, special w/ custom drawbar, or?
Hi all, I am looking at a mid 50s all lever FP1 with a MT4 to S20x2 collet adapter but would would like to use more than just collets. I would be hesitant to use standard MT drill bits as it looks...
View ArticleFP1 Horizontal Arbor Complication
Using my FP1 horizontal spindle. The Deckel arbors have a bearing surface at the outboard end that runs in the overarm support. The arbor I have to use for this particular application is not Deckel...
View ArticleKeeping in touch!
Hello All, I first wrote in April as I'd just acquired my FP1 and it had a collet adaptor stuck fast in the horizontal spindle. Many thanks for all the helpful suggestions, it came out without too much...
View ArticleSchaublin 13 high speed head mystery collet adapter
After some time of not using the high-speed head I have for my schaublin 13 due to a lack of collets (and having no idea what the collets are despite considerable research) I have started trying to...
View ArticleFP4A Contour 2 ; Error 38 ; NPP90 Eprom 44205-401.02 und 44907-461.02
Hi, I have a little Problem with an FP4A ; Contour2 When i start the machine it gives an Error Message on the screen which shows Error 38. This belongs to an Software Error on the NPP90....
View ArticleClik here to view.
What standard does Schaublin use for what they call ISO 30 Spindles
As far as I can tell the International Standards Organization does not have a standard nr 30. There is ISO 297:1988 (7/24 tapers for tool shanks for manual changing) which looks close from what I can...
View Article