Clik here to view.
i need help
hello :mad5: i'm newer in my work we use deckel maho 70 linear Evo with Itnc 530 and i study litle about heidenhian programming now i want some one help me how we do referance point ,how to use control...
View ArticleIn a pinch for dah Lih DL NC3 manuals and schematics
Hi guys.. posting here because I dunno where else. But I have the Dah Lih DL NC3, Hardhead knee mill, 5 HP Anilam 100M Fried the forward contactors today. I think the autobrake transducer isn't...
View ArticleConsidering 1979 Abene VHF-3 UBS purchase, advice please
Hi guys, I went and looked at a project abene vhf 3 with the universal table and quill. Number 5565. I say project because it is missing some parts and in not 100% working condition. I got to see and...
View ArticleAlexander milling machine manual.
Greetings all, hope I've done this right (first post). I'm in Sydney, Australia and I've been very lucky (I hope!!)) to score an Alexander mill with slotting head, universal dividing head collets &...
View ArticleDeckel FP1 spindle heat. How warm is too warm?
I've had this Deckel FP1 for a few years now but never ran the horizontal spindle until recently. (ran it with a converted Bridgeport head and had buck transformer issues that were finally resolved.)...
View ArticleThe best old "quick radial" drill I've ever seen
Otto Müller Schnellradialbohrmaschine SR 23 Radial Bohrmaschine in in München | eBay I like to check these out. The newer units are very very expensive, and the older units are usually very very beat...
View ArticleThe best old "quick radial" drill I've ever seen
Otto Müller Schnellradialbohrmaschine SR 23 Radial Bohrmaschine in in München | eBay I like to check these out. The newer units are very very expensive, and the older units are usually very very beat...
View ArticleFP2 backlash reduction - is this as good as it gets?
I have been cleaning and replacing a few parts on my FP2. I had quite a lot of backlash in my X axis. I measured it prior to replacing the leadscrew nut and it had roughly 180 degree turn of the hand...
View ArticleAbene VHF-3 Y-axis backlash adjustment? and other questions...
Hi guys, I flipped through my manual and did not see any sort of adjustment for the Y-axis backlash like there is for the X-axis backlash. Is this the case, or did I overlook something? On an unrelated...
View ArticleThe ultimate Active Deckel FP1.... with the mythical TNC123
Apparently the only manual Deckel that Luthy (Switzerland) has for sale right now.... price is probably breath taking....certainly high enough likely no danger of mucking up a deal talking about it...
View ArticleClik here to view.
Finaly got a Deckel FP1 aktiv again
This is my first activ Deckel I bought in about 4 years (yes i am a dealer) So I have to show of a bit We just replaced the leds, the frontplate for it Also some handwheelhandles and new bellows for...
View ArticleMaho 700 not started, alarm A02, lost the constant
Hello! I have problem with the Maho MH700 CNC Philips S 532. After losing the data received any machine constant and zero points but the system does not start - is the error "Measuring A02 alarm...
View ArticleFP1 leadscrew wanted
I am looking for an imperial leadscrew and nut for an FP1 No. 35784. If the price is acceptable a new one or perhaps one in good condition. I have emailed Singer via their web page a few times but no...
View ArticleClik here to view.
Photos and questions on my "new" FP1
OK, first thing I have to say is WOW! This is so much more machine than anything I have owned before. I kind of bought it on a whim so have been playing catch up trying to learn as much as possible...
View ArticleClik here to view.
Deckel Woodworking
Hi all, Just finished a Mahogany inlay in a Black Walnut cabinet door. It was a surprise anniversary gift to my wife of 25 years( she calls my Deckels the green machines) It was a reproduction of her...
View ArticleClik here to view.
Getting to know my Deckel FP1 - A small weekend project
Well, been using my FP1 quite a bit lately, doing several projects and getting more familiar with it. Like always, it never seem like one can have enough tooling...I recently bought a few MK4 collets...
View ArticleFP2 high gear tight and power feed issue
I have two strange issues with my newly acquired FP2. When I turn the dial to put the FP2 into high gear the pulley is tight and hard to turn via the rear aluminum wheel. It feels like what I would...
View ArticleClik here to view.
Deckel FP-NC Spindle Speeds
I am curious as to how the spindle speeds on an FP-NC are actually controlled. Looking at the wiring diagram it would appear the spindle motor is a simple pole changing three phase motor connected...
View ArticleDeckel LCD monitor conversion company ripped off my photo....
Kinda funny really that they have their "watermark" over my monitor conversion. And so misleading as there is so much more to converting the CRT to LCD in a Dialog 11 control than just swapping one...
View ArticleClik here to view.
Hermle UWF 802M trouble with it
I have bought this Hermle UWF802M in France Really nice machine But I have some troubles with it The spindle does not turn The powerfeeds work of and on It gets fault in the display in a more or less...
View Article