Main spindle max temperature Maho MH400E in normal range?
Hi, I have a Maho MH400e. When I run my main spindle at the maximum speed over longer periods of time the main spindle gets quite warm. I've been measuring the temperature with a contact-less laser...
View ArticleReparing relay's and beakers vs replace
I wanted to start a thread on this because I was having intermitent problems with my Deckel and with the help of DD I found the problem was a bad breaker. So after testing all by breakers with a meter...
View ArticleLoosening the pressure on sideways guide ways on deckel FP1
Hi The FP1 (dial type) is now sitting in my shop :D However the sideways movement of the working table is very tight. I have not been able to find information on how to adjust this pressure... Can...
View ArticleComparison of Deckel SOE D-bit Grinder Vs ALEXANDER 2CG TOOL AND CUTTER GRINDER
Hello just interested in comparing these two types of grinders as I am more inclined to favor the Deckel but like I said I am just wanting an open discussion about what is better reasons. My reason for...
View ArticleIndramat 3TRM2 repair tips?
Hi! Last Friday, the copper worm seems to have bitten my Indramat 3TRM2 servo amp. :( It is in a MAHO 700 C. Symptoms: X and Y (vertical mill nomenclature) do work. Z works when going downwards, and...
View ArticleAnyone have photo's of an FP1 work light set-up?
I'm looking to add a work light to my FP1 and would like to design it to fit the light port on the side of the machine. (Mine is the old style lever machine without an electrical cabinet.) Anyone have...
View ArticleTrouble Starting Maho MH 800 C
My first Post in the wrong forum (but still relevant): Hello, fellow machinists. I have a 1991 Maho MH 800 C, and I'm having trouble getting it started. I've read through many of the posts and know of...
View ArticleArboga EM825 Mill, 415V rewire to 220V questions.
So I've fell into (IE paid to much for) a Arboga EM825 Heavy mill with the 415V single voltage, 2 speed Dahlander wired motor. The good thing is that the previous owner installed an 115v 1ph, 1/2hp...
View ArticleElectrical Diagrams for 1991 Maho MH 800 C
I'm wondering if anyone has the electrical diagrams for a 1991 Maho MH 800C in a pdf for and is willing to send to me. I will be purchasing them if no one has them or no one is willing to send--I'm...
View ArticleDeckel FP1, Maho SK250 Dividing Head
If anyone has the OE Dividing head and overarm support for an FP1 or SK250 would it be possible to get the length of the overarm support please ? I have the dividing head but i'm going to have to make...
View ArticleWhat does it take to ad a 4th axis to a FP2NC with dynapath control?
Just out of curiosity, what would it take to add a 4th axis to a Deckel FP2NC with Dynapath Delta 20 control? I believe that true 4th axis is supported, though I don't know that for sure. There is...
View ArticleMy FP4NC seen within Road & Track
Some weeks ago a photographer was wondering about the shop taking snaps for a magazine.... Opened the September 2013 issue of "Road&Track" and on page 17 is a cute little snapshot of the rear of my...
View ArticleGambin-e France univ. mill to donate / scrap MONTREAL
Gambin France model 27 univ. mill : free or scrap remove at your cost Located in outskirts of Montreal in my neighbors shop. Powered up and still running well, huge mill about 1.5 to 2 x an FP4 Table...
View ArticleEllipse on Deckel dialog 3 ?
Hi I have a project with an ellipse that it would be nice to run on my FP3 with dialog 3. I can do the math for the ellipse outline using either the foci method or the concentric circle and radial...
View ArticleTable jam FP1 help
I have just bought this FP1, had the table running in auto feed x axis over to the left, the gear lever knocked out of mesh as it should, but when I tried to revers the table back it was Jammed? I have...
View ArticleDeckel FP2L... What's the design philosophy?
Hi guys, A few months ago I posted a poor pic of an FP2L. Last week I took a trip to the Big City and had a look at it in person. The dealer has had it quite a while and is so keen to sell it, they...
View ArticleAbene Help Needed
A few months ago I purchased an Abene VHF-2B made in 1966. I have gone through just about everything and have it running well, except for the power feed on the X.. I have a manual and from what I can...
View ArticleClik here to view.
FPNC recycled electrical enclosure
Hi All. It has been a while since I have posted but I wanted to show a use for a stripped for parts electrical enclosure. This one came with an FP4 my friend Steve and I bought for parts. I can only...
View ArticleEMO Ticket
The nice people at Studer sent me a ticket to the EMO show the second week of September unfortunately I will not be able to use it. This is a one day ticket so if your in Germany and planning on going...
View ArticleWhat do you use your Deckel fpnc to build?
Wanted to know what people are building with with their fpnc? To be more specific those who are making a living from there machine what have you found them to be well suited for.
View Article